Results 1 to 4 of 4

Thread: [RESOLVED] Wheel and brake problem solely in Project Cars PS4

  1. #1
    Kart Driver
    Join Date
    May 2017
    Posts
    8
    Platform
    PC

    [RESOLVED] Wheel and brake problem solely in Project Cars PS4

    I have the following problem solely in Project Cars PS4, not in other racing games.

    After updating to Thrustmaster T300 GT edition firmware 25, enabling "fan always on" option, and recalibration, I have the following problems in project cars.

    - I have the conical brake mod installed, but I get no reading from the brake pedal in the pedal calibration section (it just says "center negative" and stays on 0). In the race I only get ~30% brake power.

    - In a race, at the start or at standstill (actually at a speed of 0-3 km/hrs, thus below 4 km/hrs) the wheel quite violently pulls to full right. This happens every time the speed is 0-3 km/hrs. At higher speeds, 4km/hrs and higher the wheel behaves normally. This is quite distracting at the start.

    - In the controls menu of project cars, when touching the gas pedal, I come in the calibrate force feedback section. The game apparently thus mixes up the gas pedal with the R2 button (which is the button for entering that section).

    Please help!

  2. #2
    WMD Member BullWinkle's Avatar
    Join Date
    Mar 2012
    Location
    East Coast, Canada
    Posts
    1,177
    Platform
    PC
    Do you have 'separate pedals' selected in controller menu? ('combined pedals' would be wrong.)
    AsRock X370 Taichi MB /AMD Ryzen 1700 @ 3.4Ghz / G.SKILL Flare X Series 16GB (2 x 8GB) 288-Pin DDR4 SDRAM DDR4 3200 / Samsung NVMe SSD 960 Evo M.2
    Samsung 250GB 850 EVO (SSD) / 2 X SAPPHIRE NITRO+ Radeon RX480 8GB/OC 1342Mhz / SeaSonic Focus 750W Gold / AMD Adrenalin 18.2.1 drivers / Acer XZ271U bmijpphzx 27 Curved WQHD 2560 x 1440p 144Hz monitor.
    Windows 10 64bit / TrackIR 5, ver 5.2 final drivers / Logitech G27
    The following user likes this Post: Roger Prynne


  3. #3
    Kart Driver
    Join Date
    May 2017
    Posts
    8
    Platform
    PC
    Yes I have the separate pedals option selected (standard).
    I have also tried several times the reset option (Y) in the control menu within project cars, as well as recalibration.
    I have also tried reinstalling the Thrustmaster T300 drivers as well as the firmware 25 update, via the PC (in PS3 mode on the wheel), but no success.

    The problem persists. Strangely, in other racing games, i.e. F1 2016, and Dirt, the wheel and pedals work perfectly normal. However, Project Cars is by far my favorite!
    The following user likes this Post: BullWinkle


  4. #4
    Kart Driver
    Join Date
    May 2017
    Posts
    8
    Platform
    PC
    I have solved the issue!

    The wheel pulling to the right at low speed/standstill has been overcome by setting deadzone removal fall off to 0.01 (was 0.00)
    The brake calibration problem is overcome by setting the conical brake mod a few milimetes less tight.
    The following 3 users likes this Post: BullWinkle, Mahjik, Sankyo


Similar Threads

  1. Replies: 6
    Last Post: 25-12-2019, 05:01
  2. [RESOLVED] new problem with wheel
    By mazinga in forum PC - Technical Help & Support
    Replies: 2
    Last Post: 18-02-2017, 06:52
  3. [RESOLVED] CSW v2 + BMW M3 GT 2 rim + PS4 + Project Cars
    By shoulderdoc in forum Project CARS on Playstation 4
    Replies: 8
    Last Post: 25-07-2016, 11:27
  4. [RESOLVED] HUGE FFB problem, wheel locks when stopped, every car
    By Krus Control in forum PC - Technical Help & Support
    Replies: 35
    Last Post: 18-04-2016, 21:29
  5. Replies: 39
    Last Post: 01-03-2016, 08:27

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •